Hard reset instructionsfor Siemens SpeedStream 4100If your SpeedStream 4100 router is not working as it should, dropping connections or notbeingresponsive, you should first do a reset of the router to see if the problems persist. Otherscenarios where you might want to reset your router is if you've forgotten the password ormisconfigured it and can't get access anymore.Your can reset your Siemens SpeedStream 4100 in the following way(s):The 30-30-30 resetThere are no specific instructions for this model yet, but you can always do the 30-30-30resetas follows:. When router is powered on, press the reset button and hold for 30 seconds.
Speedstream 4100 Dsl Modem Manual
(Use a paperclipor something sharp).While holding the reset button pressed, unplug the power of the router and hold theresetbutton for 30 seconds.While still holding the reset button down, turn on the power to the unit again and holdforanother 30 seconds.This process usually works for resetting any router to it's factory setting.Note: It is worth reading more aboutand what the risks andconsiderationsare when resetting your router this way, instead of just rebooting it. How to login to the SpeedStream 4100To login to the Ethernet ADSL Modem and changethe settings, you can follow these steps:.Make sure you are connected to the router's network, either by Wi-Fi or ethernet cable.Open your browser and visit.You should be prompted with a login dialogue.Enter the username: adminand if it requires a password, leave it empty or try with admin/ passwordNote: If you have already changed the password use that instead.You will now be logged in. If you haven't yet changed the defaul password, we recommend that you change it firstthing you do after logging in.If these instructions don't work for your router, you can always try a factory reset to get the default, or trysome other common, as they canusually be shared across models/variants.
Heres what I got:Linksys WRT54G routerSeimans SPeedstream 4100 ADSL modemSBC DSL ISPUp until earlier this week I had a SS 5360 modem and it worked fine with my Linksys router, never had a problem. Then this week my modem dies. I get sent a new one from my ISP, a SS4100. Now my router cannot get an internet connection.I can get an internet connection with my computer directly connected to the modem with the modem in PPPoE mode on the modem.
I connect fine.I add in the router, I set the modem to PPPoE on the PC(middle option) and set the router to connect through PPPoE, store my username and password and it will connects, but gives me the following:IP:(dynamic address changes everytime I reconnect)subnet mask:default gateway:When I connect to just the modem, I get a mask ofAny ideas why I am getting an incorrect mask and who is to blame for the problem(SBC or Linksys)?OS: 2 comps, 1 with XP home, 1 with XP Prorouter firmware version: 1.00.6. You need to put your 4100 into 'bridge mode' when running it with a router.Type in the ip address of your speedstream 4100 into your brower, for the password use the code on the sticker on the bottom of the router. Select the bridge mode radio button and save. The 4100 will reboot and yoru will be back in business.-BrianHeres what I got:Linksys WRT54G routerSeimans SPeedstream 4100 ADSL modemSBC DSL ISPUp until earlier this week I had a SS 5360 modem and it worked fine with my Linksys router, never had a problem. Then this week my modem dies. I get sent a new one from my ISP, a SS4100. Now my router cannot get an internet connection.I can get an internet connection with my computer directly connected to the modem with the modem in PPPoE mode on the modem.
I connect fine.I add in the router, I set the modem to PPPoE on the PC(middle option) and set the router to connect through PPPoE, store my username and password and it will connects, but gives me the following:IP:(dynamic address changes everytime I reconnect)subnet mask:default gateway:When I connect to just the modem, I get a mask ofAny ideas why I am getting an incorrect mask and who is to blame for the problem(SBC or Linksys)?OS: 2 comps, 1 with XP home, 1 with XP Prorouter firmware version: 1.00.6. You need to put your 4100 into 'bridge mode' when running it with a router.Type in the ip address of your speedstream 4100 into your brower, for the password use the code on the sticker on the bottom of the router. Select the bridge mode radio button and save. The 4100 will reboot and yoru will be back in business.-BrianYour quite right about bridge mode but i would normally put the router in bridge mode not the modem, i'm not familiar with this modem though most modems aren't configurable!:!.